Camson Bluetooth Keyboard Case for iPad 2 and iPad 3: Setup

By Camera Wholesalers | Published: 2026-11-04

Category: Handleidingen

Pair and set up the Camson Bluetooth keyboard leather case for your iPad 2 or iPad 3, with a step-by-step checklist for a stable, comfortable typing stand.

Quick answer

Charge the keyboard, turn it on, and pair it once through your iPad's Bluetooth settings; then seat the iPad in the leather stand at a comfortable angle. The Camson case is built for iPad 2, iPad 3, and other 9.7-inch and earlier generations, so pairing is the same as any standard Bluetooth keyboard.

Why the Camson case suits older iPads

The Camson Wireless Bluetooth Keyboard Leather Case and Stand is made for iPad 2, iPad 3, and earlier 9.7-inch models. That focus matters because newer iPads may not align with the case cutouts, and the catalog notes the case may block the camera on newer models. If you are setting up an iPad 2 or iPad 3, the fit and stand angle are designed for that size and shape.

The leather exterior and built-in stand give you a stable typing position without a separate keyboard. The keyboard pairs over Bluetooth, so there is no cable to manage during use, but you will need to charge it before the first session.

What to check before you pair

Make sure the keyboard has enough charge for setup. The catalog does not list a battery specification or charge time, so plan to charge it fully before first use rather than guessing. Also confirm your iPad is running a version that supports Bluetooth keyboard pairing; iPad 2 and iPad 3 models can pair with standard Bluetooth keyboards, but very old iOS versions may have limited keyboard support.

Clear any previously paired keyboard from your iPad's Bluetooth list if you have used another keyboard before. This prevents the iPad from connecting to the wrong device during setup.

Step-by-step setup for the Camson keyboard case

Charge the keyboard: Connect the keyboard to a charger and let it charge fully before first use. The catalog does not specify charge time, so use the indicator or a full charge cycle as your guide. A partially charged keyboard may pair but drop the connection mid-setup.
Turn on the keyboard and enable pairing mode: Slide the power switch to on, then press and hold the pairing button (or the key combination marked for pairing) until the indicator light blinks. Check the keyboard's quick-start card if the light does not blink. If the light stays solid, the keyboard is on but not in pairing mode; repeat the hold step.
Open iPad Bluetooth settings: On your iPad, go to Settings > Bluetooth and make sure Bluetooth is turned on. Keep the settings screen open while you pair. Turning Bluetooth off and on again can clear a stuck pairing list.
Select the keyboard from the device list: Wait for the keyboard name to appear under Other Devices, then tap it. If a PIN prompt appears, type the code shown on the iPad using the keyboard and press Enter. If the keyboard does not appear, move it closer to the iPad and confirm pairing mode is still active.
Test the connection: Open Notes or any text field and type a few words. Check that every key registers and that the iPad responds without lag. If keys repeat or drop, unpair and repeat from step 2 rather than assuming a hardware fault.
Seat the iPad in the leather stand: Open the case and fold the stand into the typing position, then rest the iPad in the groove or bracket. Adjust the angle until the screen is comfortable and the iPad is stable. Avoid forcing the iPad into the stand; the leather will soften with use, but the bracket should hold without pressure.
Check camera and port access: With the iPad seated, confirm the rear camera and charging port are not blocked. The catalog notes that the case may block the camera on newer iPad models, so verify alignment on your specific iPad. If the camera is blocked on a newer iPad, remove the iPad from the case before taking photos.

Product facts

Camson Wireless Bluetooth Keyboard Leather Case and Stand for iPad 3, iPad 2 and New iPad: Designed for iPad 2, iPad 3, and earlier 9.7-inch generations; may block the camera on newer iPad models. It fits your older iPad properly, but check camera alignment if you plan to use it with a newer model.
Camson Wireless Bluetooth Keyboard Leather Case and Stand for iPad 3, iPad 2 and New iPad